Zaino fallout

393 Share

Zaino fallout

Here's the deal. Product Details For years, visual imperfections such as swirl marks, scuffs, scratches and buffer holograms were the scourge of perfectionists everywhere. It should immediately come off and leave a crystal clear finish. The spots were gone and the gloss shine was beautiful. Just make sure to keep the surface area lubricated while using the ClayBar. I wasn't sure how far I could go with removing them from a fiberglass body. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. In addition, thank you very much for emailing me the instructions on how to use the Z-PC polish.

After removal of Zaino Z-2 or Z See when your Zaino will be delivered. It's up to you Dark color surfaces, especially black, will sometimes leave you with a slightly hazy or milky surface after using Z-PC. They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. I used Z-PC and now the paint looks hazy. It should immediately come off and leave a crystal clear finish. Don't use Z-6 until you wipe the car down.

Simply follow steps 1 through 4 again. Throw the mixing bottle and any unused polish contents away after 12 hours. It contains some really great information. I did the hood, the back trunk area and some of the flat spots on the upper side. Z-PC Fusion does not have any fillers or oils. A car wash is made specifically to clean without removing durable polishes. Allow the polish the haze dry for 30 minutes. The ClayBar will get that paint finish smooth as glass. If you are looking for the ultimate paint surface preparation.

I couldn't wait to do the rest of the car! Z ClayBar is great for removing any paint surface contaminants. When satisfied with progress, continue to step 4. Product Details For years, visual imperfections such as swirl marks, scuffs, scratches and buffer holograms were the scourge of perfectionists everywhere. Does Z-PC replace Z-5? I have applied Z-2 in the Arizona sun and it dried in approx. When you are finished polishing, wash mixing bottle inside and out with a heavy concentration of liquid dish washing detergent or isopropyl alcohol and rinse thoroughly. The vial contains enough ZFX to prepare 16 ounces of polish. Clearly, I had forgotten about Zaino products and the results they can accomplish.

You be the judge I get compliments every time I drive my car now - including "thumbs up" from other drivers as they drive by my car. Tip: If more "bite" is desired, you can mist a slight amount of clean water from a spray bottle while using Z-PC Fusion. See my web site, for the real truth on cotton towels and which ones to use. You should wait 24 hours if the outside temperature is under 70 degrees and 6 hours if over 70 degrees, before applying the next coat of Z-5 or Z Note: For best results, use on a cool surface, out of direct sunlight. It's up to you. Z-2 or Z-5 does not contain any oils and once it's dry will never ever look smeary or feel greasy.

All you're accomplishing is moving it around. Does Z-PC replace Z-5? Wipe your finger on a hazed section. After 12 hours, it is not possible to remove the ZFX accelerator from the mixing bottles. Just make sure to keep the surface area lubricated while using the ClayBar. I am in complete, total AWE! A car wash is made specifically to clean without removing durable polishes. I applied it according to the directions and tried a small area.

810 Share

Zaino fallout

Z ClayBar is great for removing any paint surface contaminants. We prefer to attempt the least or non-abrasive process prior to moving on to Z-PC. Use them in the same order. Z-PC contains diminishing abrasives that are not intended for frequent use on paint finishes. Allow the polish the haze dry for 30 minutes. Sorry, but I can't help this. I look forward to purchasing more products from you. Most of my customers prefer to use Z-6 both, before and after Z-2 or Z-5 for that extra gloss boost. You can go from Z-2 to Z-5 and then back to Z-2 as often as you want.

Was this helpful? Select a moderate speed RO - 4. There's no need to wait. I came back about 20 minutes later and figured I would hose the car back off and then dry it. It has a high alkaline content which cuts right thru carnauba wax, paraffin, silicone oils, etc. We are pleased at Zaino to offer this to our customers to make your purchase even easier. See when your Zaino will be delivered. Buff the area clean with a soft, lint-free, non-marring towel. They must be Brand name Supima large white bath size towels.

Here's the deal. Don't use Z-6 until you wipe the car down. The number of coats of Z-2 or Z-5 is up to you. I would have done it but I didn't have the time. See when your Zaino will be delivered. Z ClayBar is great for removing any paint surface contaminants. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. But for an incredible Show Car finish even on a daily driver.

See when your Zaino will be delivered. I will be using Zaino products on my cars from now on! I couldn't wait to do the rest of the car! After 12 hours, it is not possible to remove the ZFX accelerator from the mixing bottles. High alkaline products like Dawn are tough on polishes. It's up to you This exclusive product allows you to create a Show Car Finish in a day and gives your car months of lasting protection. In addition, thank you very much for emailing me the instructions on how to use the Z-PC polish.

Write a Review. Z-6 can be used immediately after removing Z-2 or Z-5 or right before applying the next coat of Z-2 or Z You should always end with Z-2 as the last coat because of its higher optics. Water can also be used to minimize dusting when using a machine buffer random orbital or rotary. I couldn't wait to do the rest of the car! Use a fresh buffing towel with each coat. When I was done drying, I noticed I had water spots on several of the level surfaces of the car. Here's the deal. Yours very truly, Richard K. Was this helpful?

When you try to remove Z-2 or Z-5 when it is still wet. This exclusive product allows you to create a Show Car Finish in a day and gives your car months of lasting protection. It will never harm the paint finish though. If satisfied with the results, proceed to next section. I recommend you use my car wash Z-7 as a lubricant for the ClayBar. I get compliments every time I drive my car now - including "thumbs up" from other drivers as they drive by my car. All the areas I did looked better than the rest of the car and I thought it already looked great! See when your Zaino will be delivered. My car is black and used to look terrible - for eight 8 years, it has only gone through automatic car washers. They must be Brand name Supima large white bath size towels.

773 Share

Zaino fallout

Tip: If more "bite" is desired, you can mist a slight amount of clean water from a spray bottle while using Z-PC Fusion. The truck had streaks, fallout and minor scratches from neglect that were ALL easily taken care of with z-pc. This will remove any smears. All cars even brand new factory paint has airborne contaminants It's worth it. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. Yes No What a great product! Z-2 has higher optical properties than Z Simply follow steps 1 through 4 again. ALSO, Make sure you remove any water spots, before you apply my products.

You have the best products on the market and I thank you very much for developing such superior products. I have tried off the shelf waxes that did below par results. This exclusive product allows you to create a Show Car Finish in a day and gives your car months of lasting protection. Is this normal? When you are finished polishing, wash mixing bottle inside and out with a heavy concentration of liquid dish washing detergent or isopropyl alcohol and rinse thoroughly. I knew they had just happened so I tried to re-wash those areas thinking they had not set it, but they had. When it is not humid Z-2 will take anywhere from 30 to 60 minutes to dry. I am in complete, total AWE! All the areas I did looked better than the rest of the car and I thought it already looked great!

Wash and dry your vehicle as normal. A few people had and one guy recommended something called Zaino Z-PC. When I was done drying, I noticed I had water spots on several of the level surfaces of the car. See when your Zaino will be delivered. Start machine slowly to reduce sling. Just wipe down the car with a damp cotton towel. I would not have received the spectacular results if you did not. Shake it up and spray the area to be Clayed.

Plus higher paint protection. Usually one to two coats will accomplish that. But for an incredible Show Car finish even on a daily driver. Buff the area clean with a soft, lint-free, non-marring towel. For each ounce of polish, add 4 to 5 drops of ZFX no more than 10 drops for two full ounces , screw the cap back on, and shake vigorously for 60 to 90 seconds. Wipe your finger on a hazed section. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. All cars even brand new factory paint has airborne contaminants

When you reach the level of enhancement you like, normal maintenence with Z-7 Car Wash and Z-6 "Gloss Enhancer" spray is all that's necessary. Shake it up and spray the area to be Clayed. We are pleased at Zaino to offer this to our customers to make your purchase even easier. A car wash is made specifically to clean without removing durable polishes. Let Z-5 or Z-2 polish dry at least one hour. Just use Liquid Dawn hand dish washing liquid as a car wash. I have tried off the shelf waxes that did below par results. When satisfied with progress, continue to step 4. If you'd like call me and I'll help you out with more info!

By it's very nature as a diminishing abrasive, Z-PC breaks down the finish including Zaino polishes. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. You be the judge I couldn't wait to do the rest of the car! Also, If the humidity is high. I do not know if you are a chemist or a genius but your products are well worth the price of what you charge. The non-abrasive Z ClayBar will remove any surface contaminants from the paint finish and not hurt the clear-coat. All you're accomplishing is moving it around. Depending on how heavy you applied it.

216 Share

Zaino fallout

Simply follow steps 1 through 4 again. For each ounce of polish, add 4 to 5 drops of ZFX no more than 10 drops for two full ounces , screw the cap back on, and shake vigorously for 60 to 90 seconds. I gently worked it in for a minute or so then cleaned the product off. Does Z-PC replace Z-5? You be the judge If it smears, it is still wet. All cars even brand new factory paint has airborne contaminants A few months ago, I was washing it at home and before I could dry it off, I had to stop to help my wife with something. Wish I could upload a picture for results!

Most of my customers prefer to use Z-6 both, before and after Z-2 or Z-5 for that extra gloss boost. But for an incredible Show Car finish even on a daily driver. See when your Zaino will be delivered. Write a Review. I lived in the San Francisco Bay Area all my life where the climate is very good my plan is to return home. Z-5 is not an abrasive and can be used as often as you like. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. It is now back to the original finish! I have a Corvette which I absolutely love.

Turned a white truck into a realllly white truck. See when your Zaino will be delivered. You should always end with Z-2 as the last coat because of its higher optics. Now remember waterspots, bird droppings and bug guts if left on the paint finish for any length of time. But for an incredible Show Car finish even on a daily driver. Circular motions may be used, but always finish with front-to-back or up-and-down motions. Shake it up and spray the area to be Clayed. Just make sure to keep the surface area lubricated while using the ClayBar.

Yes No What a great product! All the areas I did looked better than the rest of the car and I thought it already looked great! We prefer to attempt the least or non-abrasive process prior to moving on to Z-PC. To test if Z-2 or Z-5 is dry and ready to be removed. When you try to remove Z-2 or Z-5 when it is still wet. Website by Silas Creative. There's no need to wait. But for this scenario it's fine.

Z-2 or Z-5 does not contain any oils and once it's dry will never ever look smeary or feel greasy. We prefer to attempt the least or non-abrasive process prior to moving on to Z-PC. To test if Z-2 or Z-5 is dry and ready to be removed. Use the polish sparingly. The ClayBar will also remove any store bought waxes. Longer drying time is necessary. I decided to give it a try and I am so glad I did. Work a small area no bigger than 2' x 2' with the Zaino Fusion, using firm motions.

Website by Silas Creative. You should wait 24 hours if the outside temperature is under 70 degrees and 6 hours if over 70 degrees, before applying the next coat of Z-5 or Z Naturally apply a coat of Z-2 or Z-5 whenever you feel it is required. Most of my customers prefer to use Z-6 both, before and after Z-2 or Z-5 for that extra gloss boost. Allow the polish the haze dry for 30 minutes. I applied it according to the directions and tried a small area. My car is black and used to look terrible - for eight 8 years, it has only gone through automatic car washers. Different situations affect drying times. I began using your wax, polish products on my Pontiac Firebird Formula in , and could not believe the results.

171 Share

Zaino fallout

It just will take much, much longer to dry. Just use Liquid Dawn hand dish washing liquid as a car wash. Buff the area clean with a soft, lint-free, non-marring towel. When you are finished polishing, wash mixing bottle inside and out with a heavy concentration of liquid dish washing detergent or isopropyl alcohol and rinse thoroughly. I began using your wax, polish products on my Pontiac Firebird Formula in , and could not believe the results. I decided to give it a try and I am so glad I did. Allow the polish the haze dry for 30 minutes. Be patient.

See my web site, for the real truth on cotton towels and which ones to use. You have the best products on the market and I thank you very much for developing such superior products. Throw the mixing bottle and any unused polish contents away after 12 hours. Was this helpful? It will never harm the paint finish though. Start machine slowly to reduce sling. One day I went on to a Corvette Forum site to see if anyone else had experienced this problem. Simply follow steps 1 through 4 again. Wash and dry your vehicle as normal. Use them in the same order.

Just the two products made my "dried up" dull paint look brand new - just as it did when I purchased the car and first used your products. Also, If the humidity is high. Note: For best results, use on a cool surface, out of direct sunlight. I knew they had just happened so I tried to re-wash those areas thinking they had not set it, but they had. Throw the mixing bottle and any unused polish contents away after 12 hours. Be patient. I applied it according to the directions and tried a small area. You can switch to Z-2 as soon as you are happy with the way the paint finish looks. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss.

The moisture in the air hinders drying time up to four times longer than normal. Naturally apply a coat of Z-2 or Z-5 whenever you feel it is required. Simply follow steps 1 through 4 again. I am in complete, total AWE! I will be using Zaino products on my cars from now on! I relocated to NW Arkansas after my father passed away in where my mother and brother have lived since A car wash is made specifically to clean without removing durable polishes. This will get your paint finish squeeky clean and wax free. Yes No. The vial contains enough ZFX to prepare 16 ounces of polish.

When satisfied with progress, continue to step 4. I did the hood, the back trunk area and some of the flat spots on the upper side. It's up to you. It should immediately come off and leave a crystal clear finish. One day I went on to a Corvette Forum site to see if anyone else had experienced this problem. If satisfied with the results, proceed to next section. They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. The ClayBar will also remove any store bought waxes. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. Wish I could upload a picture for results!

Be patient. Acquistapace 3 of 3 customers found this helpful. If satisfied with the results, proceed to next section. When you try to remove Z-2 or Z-5 when it is still wet. All cars even brand new factory paint has airborne contaminants Please read thoroughly. Yours very truly, Richard K. Work a small area no bigger than 2' x 2' with the Zaino Fusion, using firm motions. The spots were gone and the gloss shine was beautiful.

102 Share

Zaino fallout

Sorry, but I can't help this. Z-PC contains diminishing abrasives that are not intended for frequent use on paint finishes. It has a high alkaline content which cuts right thru carnauba wax, paraffin, silicone oils, etc. It's up to you Z-2 or Z-5 does not contain any oils and once it's dry will never ever look smeary or feel greasy. They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. I gently worked it in for a minute or so then cleaned the product off. If you'd like call me and I'll help you out with more info! After removal of Zaino Z-2 or Z

It will never harm the paint finish though. This will get your paint finish squeeky clean and wax free. I have been working each section at a time and the results are unbelievable! You have the best products on the market and I thank you very much for developing such superior products. I knew they had just happened so I tried to re-wash those areas thinking they had not set it, but they had. Z ClayBar is great for removing any paint surface contaminants. Buff the area clean with a soft, lint-free, non-marring towel. Plus higher paint protection.

If more buffing is required, repeat either step 2 or 3. I lived in the San Francisco Bay Area all my life where the climate is very good my plan is to return home. Depending on how heavy you applied it. Yours very truly, Richard K. The extreme weather here can destroy a cars finish. I have been working each section at a time and the results are unbelievable! Website by Silas Creative. It's up to you.

I couldn't wait to do the rest of the car! However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. You can leave Z-2 or Z-5 on for hours or overnight if you desire. Work a small area no bigger than 2' x 2' with the Zaino Fusion, using firm motions. This will get your paint finish squeeky clean and wax free. I decided to give it a try and I am so glad I did. Humidity is a killer on the drying time of Z-2 or Z Simply follow steps 1 through 4 again.

I will be using Zaino products on my cars from now on! I relocated to NW Arkansas after my father passed away in where my mother and brother have lived since I used your Z-PC polish to remove the swirls, minor scratches, and "dead" clear coat from my vehicle. Just wipe down the car with a damp cotton towel. I am not finished with the polish as I now want to apply more Z-2 coats for a show car finish. Work the product for as long as necessary - stop to occasionally check your progress. You have the best products on the market and I thank you very much for developing such superior products. They must be Brand name Supima large white bath size towels.

Wipe your finger on a hazed section. I have a Corvette which I absolutely love. They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. When you are finished polishing, wash mixing bottle inside and out with a heavy concentration of liquid dish washing detergent or isopropyl alcohol and rinse thoroughly. All cars even brand new factory paint has airborne contaminants The non-abrasive Z ClayBar will remove any surface contaminants from the paint finish and not hurt the clear-coat. I wasn't sure how far I could go with removing them from a fiberglass body. Z-5 is not an abrasive and can be used as often as you like.

338 Share

Zaino fallout

Work the product for as long as necessary - stop to occasionally check your progress. If more buffing is required, repeat either step 2 or 3. Z-2 has higher optical properties than Z Humidity is a killer on the drying time of Z-2 or Z It's up to you. The ClayBar will also remove any store bought waxes. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. It's worth it.

You should always end with Z-2 as the last coat because of its higher optics. Z-6 can be used immediately after removing Z-2 or Z-5 or right before applying the next coat of Z-2 or Z I used your Z-PC polish to remove the swirls, minor scratches, and "dead" clear coat from my vehicle. Yes No Unbelievable! The truck had streaks, fallout and minor scratches from neglect that were ALL easily taken care of with z-pc. When you try to remove Z-2 or Z-5 when it is still wet. Start with Z-AIO as per directions. If more buffing is required, repeat either step 2 or 3. I would be more than happy to endorse your products and you can publish this review on your web site.

Work the product for as long as necessary - stop to occasionally check your progress. But for an incredible Show Car finish even on a daily driver. ALSO, Make sure you remove any water spots, before you apply my products. Yours very truly, Richard K. Also, If the humidity is high. Just use Liquid Dawn hand dish washing liquid as a car wash. The non-abrasive Z ClayBar will remove any surface contaminants from the paint finish and not hurt the clear-coat. I look forward to purchasing more products from you. If you'd like call me and I'll help you out with more info! I lived in the San Francisco Bay Area all my life where the climate is very good my plan is to return home.

All cars even brand new factory paint has airborne contaminants Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. By it's very nature as a diminishing abrasive, Z-PC breaks down the finish including Zaino polishes. I would not have received the spectacular results if you did not. I have also applied it in 38 degree temperature and it took about 2 to 3 hours to dry. Also, If the humidity is high. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. Wipe your finger on a hazed section. What would have took a century with a clay bar took 30 minutes by hand with a foam applicator.

Sorry, but I can't help this. Problem areas like door handles where keys often scratch may require a few applications for best results. I am not finished with the polish as I now want to apply more Z-2 coats for a show car finish. Start machine slowly to reduce sling. Note: For best results, use on a cool surface, out of direct sunlight. All the areas I did looked better than the rest of the car and I thought it already looked great! High alkaline products like Dawn are tough on polishes. A few months ago, I was washing it at home and before I could dry it off, I had to stop to help my wife with something.

Tip: If more "bite" is desired, you can mist a slight amount of clean water from a spray bottle while using Z-PC Fusion. I would definitely recommend you remove the wax buildup on your paint. Just use Liquid Dawn hand dish washing liquid as a car wash. Wish I could upload a picture for results! The extreme weather here can destroy a cars finish. I have been working each section at a time and the results are unbelievable! To test if Z-2 or Z-5 is dry and ready to be removed. I decided to give it a try and I am so glad I did. Yes No.

573 Share

Zaino fallout

Use them in the same order. I would definitely recommend you remove the wax buildup on your paint. Wipe your finger on a hazed section. You should always end with Z-2 as the last coat because of its higher optics. Work a small area no bigger than 2' x 2' with the Zaino Fusion, using firm motions. I had two bottles of Z-6 gloss enhancer and it still works extremely well. Use a fresh buffing towel with each coat. All you're accomplishing is moving it around. Yours very truly, Richard K. When you are finished polishing, wash mixing bottle inside and out with a heavy concentration of liquid dish washing detergent or isopropyl alcohol and rinse thoroughly.

Just use Liquid Dawn hand dish washing liquid as a car wash. Yes No What a great product! See my web site, for the real truth on cotton towels and which ones to use. Naturally apply a coat of Z-2 or Z-5 whenever you feel it is required. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. Clearly, I had forgotten about Zaino products and the results they can accomplish. Allow the polish the haze dry for 30 minutes. The ClayBar will also remove any store bought waxes. My car is black and used to look terrible - for eight 8 years, it has only gone through automatic car washers. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains.

As much as two to three hours drying time is required if the temperature is 50 degrees or below. Is this normal? Tip: If more "bite" is desired, you can mist a slight amount of clean water from a spray bottle while using Z-PC Fusion. I have applied Z-2 in the Arizona sun and it dried in approx. I don't advise making a habit of washing your car with Dawn. The vial contains enough ZFX to prepare 16 ounces of polish. At one point I took my car to a detailer. By it's very nature as a diminishing abrasive, Z-PC breaks down the finish including Zaino polishes.

Will etch into the paint finish. Write a Review. I do not have many "heroes" on our planet but you are now on my humble list of them now. Depending on how heavy you applied it. High alkaline products like Dawn are tough on polishes. We are pleased at Zaino to offer this to our customers to make your purchase even easier. It's up to you Z-2 has higher optical properties than Z The number of coats of Z-2 or Z-5 is up to you. It just will take much, much longer to dry.

I get compliments every time I drive my car now - including "thumbs up" from other drivers as they drive by my car. The ZFX mixing bottles cannot be reused if the polish remains in the bottle for more than 12 hours. Dark color surfaces, especially black, will sometimes leave you with a slightly hazy or milky surface after using Z-PC. In addition, thank you very much for emailing me the instructions on how to use the Z-PC polish. Is this normal? I had two bottles of Z-6 gloss enhancer and it still works extremely well. Here's the deal. It will never harm the paint finish though.

Circular motions may be used, but always finish with front-to-back or up-and-down motions. This will get your paint finish squeeky clean and wax free. I couldn't wait to do the rest of the car! I recommend you use my car wash Z-7 as a lubricant for the ClayBar. If more buffing is required, repeat either step 2 or 3. Z-5 is not an abrasive and can be used as often as you like. Z ClayBar is great for removing any paint surface contaminants. If you are looking for the ultimate paint surface preparation.

666 Share

Zaino fallout

The ClayBar will get that paint finish smooth as glass. See my web site, for the real truth on cotton towels and which ones to use. This will get your paint finish squeeky clean and wax free. You can go from Z-2 to Z-5 and then back to Z-2 as often as you want. The vial contains enough ZFX to prepare 16 ounces of polish. We are pleased at Zaino to offer this to our customers to make your purchase even easier. Yours very truly, Richard K. I am not finished with the polish as I now want to apply more Z-2 coats for a show car finish. Buff the area clean with a soft, lint-free, non-marring towel. They must be Brand name Supima large white bath size towels.

I have a Corvette which I absolutely love. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. When it is not humid Z-2 will take anywhere from 30 to 60 minutes to dry. It contains some really great information. I recommend you use my car wash Z-7 as a lubricant for the ClayBar. It has a high alkaline content which cuts right thru carnauba wax, paraffin, silicone oils, etc. ZFX enabled polish must be applied to a clean car. There's no need to wait. Allow the polish the haze dry for 30 minutes. You can go from Z-2 to Z-5 and then back to Z-2 as often as you want.

One day I went on to a Corvette Forum site to see if anyone else had experienced this problem. Tip: If more "bite" is desired, you can mist a slight amount of clean water from a spray bottle while using Z-PC Fusion. I do not know if you are a chemist or a genius but your products are well worth the price of what you charge. Start machine slowly to reduce sling. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. The moisture in the air hinders drying time up to four times longer than normal. It's worth it. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. I use a spray bottle for the mix. But for an incredible Show Car finish even on a daily driver.

Z-2 or Z-5 does not contain any oils and once it's dry will never ever look smeary or feel greasy. The vial contains enough ZFX to prepare 16 ounces of polish. If more buffing is required, repeat either step 2 or 3. Just use Liquid Dawn hand dish washing liquid as a car wash. I use a spray bottle for the mix. Smaller towels will not work efficiently. Also, If the humidity is high. Water can also be used to minimize dusting when using a machine buffer random orbital or rotary.

For each ounce of polish, add 4 to 5 drops of ZFX no more than 10 drops for two full ounces , screw the cap back on, and shake vigorously for 60 to 90 seconds. I am in complete, total AWE! Tip: If more "bite" is desired, you can mist a slight amount of clean water from a spray bottle while using Z-PC Fusion. In addition, thank you very much for emailing me the instructions on how to use the Z-PC polish. Will etch into the paint finish. I used your Z-PC polish to remove the swirls, minor scratches, and "dead" clear coat from my vehicle. I have a Corvette which I absolutely love. High alkaline products like Dawn are tough on polishes. Also, If the humidity is high. Throw the mixing bottle and any unused polish contents away after 12 hours.

What would have took a century with a clay bar took 30 minutes by hand with a foam applicator. Problem areas like door handles where keys often scratch may require a few applications for best results. I will be using Zaino products on my cars from now on! When it is not humid Z-2 will take anywhere from 30 to 60 minutes to dry. I am not finished with the polish as I now want to apply more Z-2 coats for a show car finish. I couldn't wait to do the rest of the car! However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. Z-PC Fusion does not have any fillers or oils. Acquistapace 3 of 3 customers found this helpful.

843 Share

Zaino fallout

Throw the mixing bottle and any unused polish contents away after 12 hours. I don't advise making a habit of washing your car with Dawn. Start machine slowly to reduce sling. It is now back to the original finish! I am not finished with the polish as I now want to apply more Z-2 coats for a show car finish. It just will take much, much longer to dry. One day I went on to a Corvette Forum site to see if anyone else had experienced this problem. Work a small 2' x 2' area with moderate pressure until satisfied with results. Z-5 is not an abrasive and can be used as often as you like. Plus higher paint protection.

Also, If the humidity is high. I would have done it but I didn't have the time. See my web site, for the real truth on cotton towels and which ones to use. This exclusive product allows you to create a Show Car Finish in a day and gives your car months of lasting protection. Turned a white truck into a realllly white truck. Circular motions may be used, but always finish with front-to-back or up-and-down motions. I do not know if you are a chemist or a genius but your products are well worth the price of what you charge. I get compliments every time I drive my car now - including "thumbs up" from other drivers as they drive by my car. Note: For best results, use on a cool surface, out of direct sunlight. Just make sure to keep the surface area lubricated while using the ClayBar.

Yours very truly, Richard K. I had two bottles of Z-6 gloss enhancer and it still works extremely well. Please read thoroughly. After 12 hours, it is not possible to remove the ZFX accelerator from the mixing bottles. Shake it up and spray the area to be Clayed. I knew they had just happened so I tried to re-wash those areas thinking they had not set it, but they had. Select a moderate speed RO - 4. It should immediately come off and leave a crystal clear finish. A few months ago, I was washing it at home and before I could dry it off, I had to stop to help my wife with something.

Also, If the humidity is high. Start machine slowly to reduce sling. The non-abrasive Z ClayBar will remove any surface contaminants from the paint finish and not hurt the clear-coat. Wipe your finger on a hazed section. A few people had and one guy recommended something called Zaino Z-PC. Work a small 2' x 2' area with moderate pressure until satisfied with results. We are pleased at Zaino to offer this to our customers to make your purchase even easier. You can leave Z-2 or Z-5 on for hours or overnight if you desire. Now remember waterspots, bird droppings and bug guts if left on the paint finish for any length of time.

When satisfied with progress, continue to step 4. Problem areas like door handles where keys often scratch may require a few applications for best results. High alkaline products like Dawn are tough on polishes. Humidity is a killer on the drying time of Z-2 or Z It just will take much, much longer to dry. Yours very truly, Richard K. The truck had streaks, fallout and minor scratches from neglect that were ALL easily taken care of with z-pc. Be patient. Simply follow steps 1 through 4 again. For the next few months they really bothered me and I tried a couple of non-invasive approaches to removing them but nothing worked.

Website by Silas Creative. Naturally apply a coat of Z-2 or Z-5 whenever you feel it is required. I have also applied it in 38 degree temperature and it took about 2 to 3 hours to dry. The ClayBar will also remove any store bought waxes. If satisfied with the results, proceed to next section. Circular motions may be used, but always finish with front-to-back or up-and-down motions. The number of coats of Z-2 or Z-5 is up to you. High alkaline products like Dawn are tough on polishes. The spots were gone and the gloss shine was beautiful. It is now back to the original finish!

435 Share

Zaino fallout

I applied it according to the directions and tried a small area. Water can also be used to minimize dusting when using a machine buffer random orbital or rotary. It's worth it. Z-2 has higher optical properties than Z We are pleased at Zaino to offer this to our customers to make your purchase even easier. Now remember waterspots, bird droppings and bug guts if left on the paint finish for any length of time. This will remove any smears. Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. Yes No What a great product! If you'd like call me and I'll help you out with more info!

Smaller towels will not work efficiently. When you reach the level of enhancement you like, normal maintenence with Z-7 Car Wash and Z-6 "Gloss Enhancer" spray is all that's necessary. The non-abrasive Z ClayBar will remove any surface contaminants from the paint finish and not hurt the clear-coat. By it's very nature as a diminishing abrasive, Z-PC breaks down the finish including Zaino polishes. Plus higher paint protection. Problem areas like door handles where keys often scratch may require a few applications for best results. I am in complete, total AWE! Website by Silas Creative.

Smaller towels will not work efficiently. I am in complete, total AWE! After removal of Zaino Z-2 or Z Z-5 is not an abrasive and can be used as often as you like. Was this helpful? Website by Silas Creative. Problem areas like door handles where keys often scratch may require a few applications for best results. I lived in the San Francisco Bay Area all my life where the climate is very good my plan is to return home. It's worth it.

This will get your paint finish squeeky clean and wax free. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. Smaller towels will not work efficiently. I lived in the San Francisco Bay Area all my life where the climate is very good my plan is to return home. Buff the area clean with a soft, lint-free, non-marring towel. Circular motions may be used, but always finish with front-to-back or up-and-down motions. Z-PC contains diminishing abrasives that are not intended for frequent use on paint finishes. Use the polish sparingly. It really helps give a three dimensional look.

Use the polish sparingly. There's no need to wait. When satisfied with progress, continue to step 4. All the areas I did looked better than the rest of the car and I thought it already looked great! Start with Z-AIO as per directions. Does Z-PC replace Z-5? Problem areas like door handles where keys often scratch may require a few applications for best results. Wipe your finger on a hazed section. ZFX enabled polish must be applied to a clean car. You can switch to Z-2 as soon as you are happy with the way the paint finish looks.

It really helps give a three dimensional look. A car wash is made specifically to clean without removing durable polishes. Allow the polish the haze dry for 30 minutes. All cars even brand new factory paint has airborne contaminants Depending on how heavy you applied it. Note: For best results, use on a cool surface, out of direct sunlight. You can leave Z-2 or Z-5 on for hours or overnight if you desire. Website by Silas Creative. The extreme weather here can destroy a cars finish. Use a fresh buffing towel with each coat.

411 Share

Zaino fallout

I applied it according to the directions and tried a small area. Wash and dry your vehicle as normal. Now, it was not easy as there was so much neglect and "stains" in the finish. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. I wasn't sure how far I could go with removing them from a fiberglass body. Z-2 has higher optical properties than Z Product Details For years, visual imperfections such as swirl marks, scuffs, scratches and buffer holograms were the scourge of perfectionists everywhere. Let Z-5 or Z-2 polish dry at least one hour.

You be the judge The ZFX mixing bottles cannot be reused if the polish remains in the bottle for more than 12 hours. Be patient. Problem areas like door handles where keys often scratch may require a few applications for best results. High alkaline products like Dawn are tough on polishes. Acquistapace 3 of 3 customers found this helpful. Turned a white truck into a realllly white truck. Allow the polish the haze dry for 30 minutes. Simply follow steps 1 through 4 again. Was this helpful?

It just will take much, much longer to dry. Simply follow steps 1 through 4 again. Start with Z-AIO as per directions. Z-2 has higher optical properties than Z Z-6 can be used immediately after removing Z-2 or Z-5 or right before applying the next coat of Z-2 or Z I used Z-PC and now the paint looks hazy. The ClayBar will get that paint finish smooth as glass. Website by Silas Creative. The number of coats of Z-2 or Z-5 is up to you.

If you are looking for the ultimate paint surface preparation. You should always end with Z-2 as the last coat because of its higher optics. The ClayBar will get that paint finish smooth as glass. I will be using Zaino products on my cars from now on! All cars even brand new factory paint has airborne contaminants Yours very truly, Richard K. The extreme weather here can destroy a cars finish. I have applied Z-2 in the Arizona sun and it dried in approx. Wash and dry your vehicle as normal.

Be patient. I use a spray bottle for the mix. Website by Silas Creative. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. Now remember waterspots, bird droppings and bug guts if left on the paint finish for any length of time. I relocated to NW Arkansas after my father passed away in where my mother and brother have lived since I have applied Z-2 in the Arizona sun and it dried in approx. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. Select a moderate speed RO - 4.

Plus higher paint protection. Circular motions may be used, but always finish with front-to-back or up-and-down motions. You should wait 24 hours if the outside temperature is under 70 degrees and 6 hours if over 70 degrees, before applying the next coat of Z-5 or Z Was this helpful? This exclusive product allows you to create a Show Car Finish in a day and gives your car months of lasting protection. Dark color surfaces, especially black, will sometimes leave you with a slightly hazy or milky surface after using Z-PC. I do not know if you are a chemist or a genius but your products are well worth the price of what you charge. I get compliments every time I drive my car now - including "thumbs up" from other drivers as they drive by my car. If you'd like call me and I'll help you out with more info!

885 Share

Zaino fallout

If you remove Z-2 or Z-5 before it is thoroughly dry and get any smears. One day I went on to a Corvette Forum site to see if anyone else had experienced this problem. See when your Zaino will be delivered. They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. You can switch to Z-2 as soon as you are happy with the way the paint finish looks. I have applied Z-2 in the Arizona sun and it dried in approx. I would be more than happy to endorse your products and you can publish this review on your web site. Work the product for as long as necessary - stop to occasionally check your progress. Just use Liquid Dawn hand dish washing liquid as a car wash. Z ClayBar is great for removing any paint surface contaminants.

Throw the mixing bottle and any unused polish contents away after 12 hours. Yes No Unbelievable! I couldn't wait to do the rest of the car! Please read thoroughly. Work a small area no bigger than 2' x 2' with the Zaino Fusion, using firm motions. The truck had streaks, fallout and minor scratches from neglect that were ALL easily taken care of with z-pc. This exclusive product allows you to create a Show Car Finish in a day and gives your car months of lasting protection. They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. This will get your paint finish squeeky clean and wax free.

Product may be used in the sun or on a hot surface, but more dusting and minor streaking may occur. Clearly, I had forgotten about Zaino products and the results they can accomplish. Throw the mixing bottle and any unused polish contents away after 12 hours. My car is black and used to look terrible - for eight 8 years, it has only gone through automatic car washers. All you're accomplishing is moving it around. Start with Z-AIO as per directions. If you'd like call me and I'll help you out with more info! When I was done drying, I noticed I had water spots on several of the level surfaces of the car. Plus higher paint protection. Use the polish sparingly.

Also, If the humidity is high. Website by Silas Creative. In addition, thank you very much for emailing me the instructions on how to use the Z-PC polish. Just use Liquid Dawn hand dish washing liquid as a car wash. Just wipe down the car with a damp cotton towel. I look forward to purchasing more products from you. Just make sure to keep the surface area lubricated while using the ClayBar. It contains some really great information. Yes No What a great product!

Z-2 has higher optical properties than Z They infected vehicles without any discrimination - show cars, daily drivers, imports, domestics and custom vehicles all suffered. It really helps give a three dimensional look. All cars even brand new factory paint has airborne contaminants What would have took a century with a clay bar took 30 minutes by hand with a foam applicator. Be patient. A few months ago, I was washing it at home and before I could dry it off, I had to stop to help my wife with something. The number of coats of Z-2 or Z-5 is up to you. The non-abrasive Z ClayBar will remove any surface contaminants from the paint finish and not hurt the clear-coat.

I am in complete, total AWE! But for an incredible Show Car finish even on a daily driver. However, Multiple coats will achieve an even deeper, wetter-looking, ultra high gloss. When you reach the level of enhancement you like, normal maintenence with Z-7 Car Wash and Z-6 "Gloss Enhancer" spray is all that's necessary. Because Zaino has no abrasives or harsh solvents it will not remove water spots or stains. For the next few months they really bothered me and I tried a couple of non-invasive approaches to removing them but nothing worked. It's up to you. Wash and dry your vehicle as normal.

Zaino jansport kohls

About Moogujind

Z-PC contains diminishing abrasives that are not intended for frequent use on paint finishes. A few months ago, I was washing it at home and before I could dry it off, I had to stop to help my wife with something.

Related Posts

197 Comments

Post A Comment